Boonton 4530 Peak Power Meter User Manual Manual do Utilizador descarregar pdf (Página 133)

4-59

Boonton Electronics Chapter 4

4530 Series RF Power Meter Remote Operation

SENSe[1 | 2]:PULse:DISTal <n> set/return pulse distal level in percent of top power, <n> = 0 to 100%

SENSe[1 | 2]:PULse:MESIal <n> set/return pulse mesial level in percent of top power, <n> = 0 to 100%

SENSe[1 | 2]:PULse:PROXimal <n> set/return pulse proximal level in % of top power, <n> = 0 to 100%

SENSe[1 | 2]:PULse:UNITs <asc> set/return power units used for DIST, MESI and PROX arguments

SENSe[1 | 2]:PULse:STARTGT <n> set/return pulse gate start in % of pulse duration, <n> = 0 to 40%

SENSe[1 | 2]:PULse:ENDGT <n> set/return pulse gate end in % of pulse duration, <n> = 60 to 100%

SENSe[1 | 2]:HIST:COUNt <n> set/return the number of histogram bins to return, <n> = 0 to 4096

SENSe[1 | 2]:HIST:INDEX <n> set/return index of first histogram bin to return, <n> = 0 to 4095

SENSe[1 | 2]:HIST:DATA? return “count” bin values from the signal histogram, starting at “index”

SENSe[1 | 2]:CALTAB:COUNt <n> set/return the number of cal table values to return, <n> = 0 to 4096

SENSe[1 | 2]:CALTAB:INDEX <n> set/return index of first cal table value to return, <n> = 0 to 4095

SENSe[1 | 2]:CALTAB:DATA? return “count” power values from the cal table, starting at “index”.

SENSe[1 | 2]:MBUF:SIZe <n> set/return the number readings needed to fill meas buffer, <n> = 0 to 4096

SENSe[1 | 2]:MBUF:RATe <n> set/return meas buffer rate for Mod & CW, <n> = 1 to 1000 rdgs/sec

SENSe[1 | 2]:MBUF:POSition? return current acquisition index position of measurement buffer

SENSe[1 | 2]:MBUF:COUNt <n> set/return the number of meas buffer readings to return, <n> = 0 to 4096

SENSe[1 | 2]:MBUF:INDEX <n> set/return index of first meas buffer reading to return, <n> = 0 to 4095

SENSe[1 | 2]:MBUF:DATA? return “count” stored readings from the meas buffer, starting at “index”

SENSe[1 | 2]:SBUF:MODE <asc> set/return status of user defined sample buffer, <asc> = ON, OFF

SENSe[1 | 2]:SBUF:PERiod <n> set/return the A/D sampling period, <n> = 5 to 12,500

SENSe[1 | 2]:SBUF:PREsamp <n> set/return the number of samples before the trigger, <n> = 0 to 12,000

SENSe[1 | 2]:SBUF:POSTsamp <n> set/return the number of samples after the trigger, <n> = 0 to 12,000

SENSe[1 | 2]:SBUF:COUNt<n> set/return the total number of samples to return, <n> = 1 to 12,000

SENSe[1 | 2]:SBUF:INDEX <n> set/return the index of next data point relative to trigger position

SENSe[1 | 2]:SBUF:DATA? return “count” power samples from captured buffer starting at “index”.

SENSe[1 | 2]:TEMPerature? return sensor internal temperature in degrees Celsius

SENSe[1 | 2]:CALTemp? return sensor calibration temperature in degrees Celsius

STATus:PRESet set device dependent SCPI and device status registers

STATus:OPERation:EVENt? return value of Operation Status Register

STATus:OPERation:CONDition? return value of Operation Condition Register (unlatched)

STATus:OPERation:ENABle <n> set/return value of Operation Enable Mask, <n> = 0 to 32767

STATus:QUEStionable:EVENt? return value of Questionable Status Register

STATus:QUEStionable:CONDition? return value of Questionable Condition Register (unlatched)

STATus:QUEStionable:ENABle <n> set/return value of Questionable Enable Mask, <n> = 0 to 32767

SYSTem:BEEP <asc> set/return keypad audible beeper status, <asc> = ON, OFF

SYSTem:ERRor[:NEXT]? return next queued error code number and description

SYSTem:COMMunicate:SERial:BAUD <n> set/return serial port baud rate, <n> = 1200 to 38400 baud

SYSTem:COMMunicate:SERial:BITS <n> set/return number of serial port data bits, <n> = 7 or 8

SYSTem:COMMunicate:SERial:SBITs <n> set/return number of serial port stop bits, <n> = 1 or 2

SYSTem:COMMunicate:SERial:PARity <asc> set/return state of serial port parity bit, <asc> = NONE, ODD, EVEN

SYSTem:COMMunicate:SERial:CONTrol:RTS <asc> set/return serial RTS handshake mode: OFF, ON

Table 4-1 Remote Command Summary (Cont)

1 2 ... 128 129 130 131 132 133 134 135 136 137 138 ... 169 170

Comentários a estes Manuais

Sem comentários

Boonton 4530 Peak Power Meter User Manual Manual do Utilizador Página 133

Comentários a estes Manuais

Manuais e produtos relacionados com Instrumentos de medida Boonton 4530 Peak Power Meter User Manual